Configurable Walk-Behind Fork Stackers – Manual & Electric Lift

Quick answer: This configurable walk-behind fork stacker family combines manual hydraulic, powered-lift, C-channel and double-mast versions in one selection range. Choose by actual load, lift height, pallet entry and lifting frequency: the listed configurations cover 200–2,000 kg loads and 1.6–4.5 m lift heights, while higher-lift models carry less weight.

Choose a Fork Stacker by Workload, Not by Label

Moving palletized loads in a compact warehouse should not mean overspending on a powered forklift or asking operators to pump heavy loads through every shift. This KINGRISE fork stacker series lets warehouses, workshops, production lines and distribution centers match the lifting method and mast structure to the actual task instead of choosing from a generic “1 ton” or “2 ton” label.

• Manual hydraulic stackers: a straightforward, low-maintenance choice for occasional lifts and shorter duty cycles.
• Semi-electric and electric-lift stackers: reduce repetitive pumping during frequent loading, positioning and stacking tasks.
• C-channel manual stackers: reinforced channel-steel construction for demanding material-handling applications.
• Double-mast electric-lift stackers: reach up to 4.5 m where higher stacking is required and the load is lighter.

Walk-Behind Fork Stacker Configuration Matrix

Capacity and lift height are configuration-specific. The 2,000 kg configuration requires engineering confirmation before ordering. Do not assume that the maximum capacity applies at the maximum lift height.

Key Dimensions and Operating Limits

Dimensions vary by configuration and may vary slightly with production tolerances. Request a confirmed drawing before ordering or planning aisle clearance.

Match the Configuration to the Bottleneck

• Too much operator pumping: choose powered lift for repeated vertical handling during a shift.
• Limited aisle or doorway space: compare the actual overall width, turning clearance and lowered mast height with your route.
• High rack position: use the double-mast range, but select from the lower rated capacities shown for 2.5–4.5 m lifts.
• Uncertain pallet fit: verify pallet entry direction, bottom-board design, fork spread, inner-leg width and load center before purchase.
• Non-standard loads: send the load dimensions, center of gravity and required fork dimensions for a custom recommendation.

What to Send for Model Confirmation

Send the load weight and dimensions, required lift height, pallet type and entry direction, fork dimensions, aisle and doorway measurements, lifting cycles per shift, power supply, destination country and order quantity. KINGRISE can then confirm the suitable configuration instead of relying on capacity alone.

Frequently Asked Questions

Which configuration should I choose for repeated lifting during a shift?

Choose a powered-lift configuration when repeated pumping is the main operator bottleneck. Keep the manual hydraulic version for occasional lifts where simplicity and low maintenance matter more than cycle speed. State the expected lifting cycles per shift so KINGRISE can check the motor, battery and duty requirement.

Can the 4.5 m model lift 2,000 kg?

No such combination is shown in the supplied specifications. The listed 4.5 m double-mast model is rated at 200 kg. Higher lift height and higher capacity must be evaluated together; ask KINGRISE to confirm the load chart for your load center.

Will the stacker work with my pallets?

That depends on the pallet's entry direction, bottom-board structure, opening width and load center. Send a pallet drawing or clear measurements so the fork spread and straddle-leg clearance can be checked before production.

Is the electric version self-propelled?

The supplied configurations show powered lifting with walk-behind travel. Do not assume powered travel is included. If you need traction drive for ramps, long travel distances or heavy daily use, state that requirement in your inquiry.

How do I check whether it will fit a narrow aisle?

Compare more than the frame width. Check overall length, turning clearance with the pallet loaded, doorway width, floor condition and the mast height in its lowered position.

Can fork width, lift height or capacity be customized?

Customization is available, subject to engineering review. Provide the load, load center, pallet dimensions, target height and duty cycle so KINGRISE can confirm a safe configuration.

What should I provide to receive a useful quotation?

Provide rated load, maximum lift height, pallet and load dimensions, aisle and doorway sizes, lifting frequency, destination, quantity and any voltage or OEM requirements. This prevents a price quote for equipment that does not fit the actual workflow.

Need a different pallet-handling design? View all KINGRISE hydraulic pallet stackers, or contact KINGRISE with your load, pallet and lift-height requirements for configuration support and B2B pricing.